-40%

63" 1600mm Full Auto Hot Cold Roll Laminator Machine Wide Format Laminating - US

$ 949.87

Availability: 10 in stock
  • Return shipping will be paid by: Buyer
  • Power Supply: AC110V, 50 / 60Hz
  • Power: 2200W
  • Maximum Laminating Thickness: 25mm (0.99")
  • Control Type: Full Auto
  • Restocking Fee: No
  • Brand: Unbranded
  • Condition: New
  • Roller’s Diameter: 130mm (5")
  • All returns accepted: Returns Accepted
  • Item must be returned within: 60 Days
  • Maximum Laminator Width: 1520mm (60")
  • Preheating Time: 5 - 10mins
  • Refund will be given as: Money Back
  • MPN: Does Not Apply

    Description

    60" Full Auto Cold Roll Laminator Large Format Laminating Machine Heat Assisted
    US Stock
    LOCAL PICK UP ONLY !
    DOOR to DOOR Service.
    No Cutoms Troubles !
    3 YEARS WARRANTY!
    Buy with confidence!
    You buy,we assume all responsibility!
    Kindly Note: Not Include the Air Compressor !!!
    Warm tips:
    we have USA warehouse, it can save much shipping fee and time for you .
    All of our products are high quality , perfect aftersales service. please buy with confidence!
    Any questions, plz send us message, we will do our
    best for you .
    Details:
    This 60" Full - auto Low Temp
    Wide Format cold laminator
    with Stand can be widely used for pre - masking vinyl graphic, mount prints on substrate, over laminating inkjet prints and so on.
    The cold laminator is used to after printing. Available for photographic, Ad. Shop and copy shop to do lamination work, adding a protective layer on books cover, photographic, color pages, documents, charts, drawings, indoor advertising products, etc.
    This laminator 1600C6+ is
    low heated cold laminator
    with liner and without
    liner, a wide range of application.
    It can be used
    both cold laminating and hot laminating
    with low temperature, to strip coil backing paper,to roll picture
    automatically.
    Especially when work in hot laminating conditions,it will improve the
    coating effect by heating the roller,.
    It’s multiple-function,easy operation and high efficiency.
    Single side lifting roller, easy to adjust the open height of roller (the laminating thickness). Support roll to roll operation, which saves labor.
    Good color reducibility and light transmittance, free of bubbles and snowflake point!
    Description:
    Model
    SEC-010
    Maximum Laminator Width
    1520mm (60")
    Roller’s Diameter
    130mm (5")
    Maximum Laminating Thickness
    25mm (0.99")
    Maximum Heating Temperature
    when hot laminating, the temperature is 50~60 degree, the highest
    temperature is 60 degree.
    Laminating Speed
    From
    0 to 10m (393")
    per minute
    Preheating Time
    5 - 10mins
    Power Consumption
    0.3 - 0.5KW / h
    Power Input
    2200W
    Height Adjust
    Single side lifting link
    Motor Forward / Reverse
    Yes
    Floor Stand
    Yes
    Auto Rewind Liner Pickup
    Yes
    After Laminating Pickup
    Yes
    Emergency Stops
    Yes
    Safety Photocell
    Yes
    Power Supply
    AC110V, 50 / 60Hz
    Features:
    Adopts low temperature cold laminating, mainly used to solve the issue that cold laminated images are hazy.
    Stainless steel feeding table
    130mm (5") upper rubber roller
    Auto – take – up system
    Anti – tilt and anti – fold device (Origin)
    Pressure and height adjust hand wheel
    Infrared temperature control device
    Details
    Control Panel
    using Instruction:
    Preset temperature: Find out hot/cold framed switch, choose the "hot ", temperature display screen will light up, the left number is preset temperature, the right number is roller temperature, press “■ SET”key and then through “▲ UP” and“▼
    DOWN” adjust preset temperature, after adjust it and press“■ SET”key confirm it. when cold film, the preset temperature is 50 ℃ .,the max temperature is 50 ℃.According to the viscosity of the glue, and adjust preset temperature.
    Turn: This machine don’t have continuous reverse function;
    In the "continuous" state it only can " turning";
    In the "point move" state, through the pedal switch can "turning" or "reverse".
    Governor knob: clockwise to grow speed, counter-clockwise to slow down; Please select the appropriate speed to ensure the laminating effect, when stop coated please select "point move".
    Working  Diagram
    General Using and installation method
    Note:The hex nuts must be tighten! If loose will appear heating power electric spark change,and broken wire and other components.
    Film laminating
    Laminating work is an extremely fine, technical stronger work, for beginners should have experience in the technicians under guidance of Membranae tectoria work, the below only show the general operation.
    Preheating ready to work:
    1. Fall down tne upper nip roller;
    2. Press the "continuous" and "turning" switch, governor rotate to the "1";
    3. Open the main switch;
    4. Open the "hot" switch and et the heat temperature which we required, then nip roller began to heating. Hot laminating, the preset temperature is 90 ℃ , when low temperature/cold laminating, the preset temperature set to 45 ℃ (to working temperature need about 10-20 minutes)
    5. Take out a roll of film and install into material roller, then let roll into material feeding roller scaffold and pulling the film with the hand, shall ensure the appropriate resistance,through the next to the damping handwheel adjust it.
    6. Let framed chart scroll in carton, then packed in rewinding stent and fixed them.
    The general questions and methods
    Problem
    Control panel have no electricity
    Method:
    Check the power and emergency button
    Problem
    Don’t turn
    Method:
    Lift a little the upper roller
    Adjust friction
    Tighten sprocket key
    Contact with motor or governor
    Problem
    Laminated paper isn't clear and have white point
    Method:
    Increase roller temperature
    Clean the dust
    Contact suppliers to replace film
    Problem
    laminated paper have pleated bubbles
    Method:
    Adjust roller force
    Put paper in 90 angle into rubber roller
    Increase speed and reduce temperature
    Problem
    Film fold
    Method:
    Adjust material-roller’s resistance
    Adjust to the required temperature
    Package:
    The laminator comes with 2pcs of heating glass tube, 1pcs is on the machine, 1 pc is in
    another package. We send the spare 1 pc of it just in case of any damage during the
    shipping.
    If the one on the machine damaged, please use the spare 1 pc replace it.
    We will not accept any complaint of the tube damaged.
    Machine Dimension
    74" x 27" x 45" (1880mm x 680mm x 1140mm)
    Machine Weight
    280lb (140kg)
    Package
    Fumigation free package
    Packing Size
    81" x 28" x 28" (2060mm x 710mm x 720mm)
    Gross Weight
    441lb (200kg)
    Table 1: Accessories
    Term
    Quantity
    Notice
    Backing sheet reception roll
    1
    Feeding roll
    1
    Film roll
    1
    Black rubber beam weight
    1
    Finished products roll
    1
    Hand wheel
    1
    Rubber mat
    1
    Left support of feeding roll
    1
    Right support of feeding roll
    1
    Fuse
    4
    2A/7A
    Video
    1
    Application
    Applying to indoor and outdoor car sticker,photo and video,rimless no painting mounting and so on.
    SHIPPING
    1.We will ship your item by FedEx, DHL, UPS, EMS, e-Package etc with the tracking number showed on ebay.
    2.Your item will be shipped within 1-3 working days after clear payment .
    3.The shipping time varies. If by FedEX, DHL,or UPS, 3-4 business days to USA,5-7 business days to other most countries.
    If by e-packet,7-15 days to USA,and 2-4 weeks to other most countries.
    4.Due to the local dispatch or other reasons, sometimes the shipping time will be delay. Please kindly understand Uncertainties by the delivery company. We will track the item all the time until it is reached to you.
    PAYMENTS
    1. we accept: Paypal and some other payment method.
    2. We will very appreciate if you can pay for the order after your ordering within 1-3 working days so that we can provide you the best services.
    3. Please list your special requests in Note after payment. (color, packages, etc.)
    Feedback
    1.If you have any problems or concerns to your order or products, please message us and give us a chance to assist before you leave negative feedback.
    2.We believe that we can produce a positive outcome to any situation to earn your like
    s.
    3.Your satisfaction is guaranteed.