60" Full Auto Cold Roll Laminator Large Format Laminating Machine Heat Assisted

Description

60" Full Auto Cold Roll Laminator Large Format Laminating Machine Heat Assisted
US Stock
Fast shipping
within 24 hours
!
DOOR to DOOR Service.
No Cutoms Troubles !
3 YEARS WARRANTY!
Buy with confidence!
You buy,we assume all responsibility!
Local pic up is ok,email us freely.
Kindly Note: Not Include the Air Compressor !!!
Warm tips:
we have USA warehouse, it can save much shipping fee and time for you .
All of our products are high quality , perfect aftersales service. please buy with confidence!
Any questions, plz send us message, we will do our
best for you .
Details:
This 60" Full - auto Low Temp
Wide Format cold laminator
with Stand can be widely used for pre - masking vinyl graphic, mount prints on substrate, over laminating inkjet prints and so on.
The cold laminator is used to after printing. Available for photographic, Ad. Shop and copy shop to do lamination work, adding a protective layer on books cover, photographic, color pages, documents, charts, drawings, indoor advertising products, etc.
This laminator 1600C6+ is
low heated cold laminator
with liner and without
liner, a wide range of application.
It can be used
both cold laminating and hot laminating
with low temperature, to strip coil backing paper,to roll picture
automatically.
Especially when work in hot laminating conditions,it will improve the
coating effect by heating the roller,.
It’s multiple-function,easy operation and high efficiency.
Single side lifting roller, easy to adjust the open height of roller (the laminating thickness). Support roll to roll operation, which saves labor.
Good color reducibility and light transmittance, free of bubbles and snowflake point!
Description:
Model
SEC-010
Maximum Laminator Width
1520mm (60")
Roller’s Diameter
130mm (5")
Maximum Laminating Thickness
25mm (0.99")
Maximum Heating Temperature
when hot laminating, the temperature is 50~60 degree, the highest
temperature is 60 degree.
Laminating Speed
From
0 to 10m (393")
per minute
Preheating Time
5 - 10mins
Power Consumption
0.3 - 0.5KW / h
Power Input
2200W
Height Adjust
Single side lifting link
Motor Forward / Reverse
Yes
Floor Stand
Yes
Auto Rewind Liner Pickup
Yes
After Laminating Pickup
Yes
Emergency Stops
Yes
Safety Photocell
Yes
Power Supply
AC110V, 50 / 60Hz
Features:
Adopts low temperature cold laminating, mainly used to solve the issue that cold laminated images are hazy.
Stainless steel feeding table
130mm (5") upper rubber roller
Auto – take – up system
Anti – tilt and anti – fold device (Origin)
Pressure and height adjust hand wheel
Infrared temperature control device
Details
Control Panel
using Instruction:
Preset temperature: Find out hot/cold framed switch, choose the "hot ", temperature display screen will light up, the left number is preset temperature, the right number is roller temperature, press “■ SET”key and then through “▲ UP” and“▼
DOWN” adjust preset temperature, after adjust it and press“■ SET”key confirm it. when cold film, the preset temperature is 50 ℃ .,the max temperature is 50 ℃.According to the viscosity of the glue, and adjust preset temperature.
Turn: This machine don’t have continuous reverse function;
In the "continuous" state it only can " turning";
In the "point move" state, through the pedal switch can "turning" or "reverse".
Governor knob: clockwise to grow speed, counter-clockwise to slow down; Please select the appropriate speed to ensure the laminating effect, when stop coated please select "point move".
Working  Diagram
General Using and installation method
Note：The hex nuts must be tighten! If loose will appear heating power electric spark change,and broken wire and other components.
Film laminating
Laminating work is an extremely fine, technical stronger work, for beginners should have experience in the technicians under guidance of Membranae tectoria work, the below only show the general operation.
Preheating ready to work:
1. Fall down tne upper nip roller;
2. Press the "continuous" and "turning" switch, governor rotate to the "1";
3. Open the main switch;
4. Open the "hot" switch and et the heat temperature which we required, then nip roller began to heating. Hot laminating, the preset temperature is 90 ℃ , when low temperature/cold laminating, the preset temperature set to 45 ℃ (to working temperature need about 10-20 minutes)
5. Take out a roll of film and install into material roller, then let roll into material feeding roller scaffold and pulling the film with the hand, shall ensure the appropriate resistance,through the next to the damping handwheel adjust it.
6. Let framed chart scroll in carton, then packed in rewinding stent and fixed them.
The general questions and methods
Problem
Control panel have no electricity
Method:
Check the power and emergency button
Problem
Don’t turn
Method:
Lift a little the upper roller
Adjust friction
Tighten sprocket key
Contact with motor or governor
Problem
Laminated paper isn't clear and have white point
Method:
Increase roller temperature
Clean the dust
Contact suppliers to replace film
Problem
laminated paper have pleated bubbles
Method:
Adjust roller force
Put paper in 90 angle into rubber roller
Increase speed and reduce temperature
Problem
Film fold
Method:
Adjust material-roller’s resistance
Adjust to the required temperature
Package:
The laminator comes with 2pcs of heating glass tube, 1pcs is on the machine, 1 pc is in
another package. We send the spare 1 pc of it just in case of any damage during the
shipping.
If the one on the machine damaged, please use the spare 1 pc replace it.
We will not accept any complaint of the tube damaged.
Machine Dimension
74" x 27" x 45" (1880mm x 680mm x 1140mm)
Machine Weight
280lb (140kg)
Package
Fumigation free package
Packing Size
81" x 28" x 28" (2060mm x 710mm x 720mm)
Gross Weight
441lb (200kg)
Table 1: Accessories
Term
Quantity
Notice
Backing sheet reception roll
1
Feeding roll
1
Film roll
1
Black rubber beam weight
1
Finished products roll
1
Hand wheel
1
Rubber mat
1
Left support of feeding roll
1
Right support of feeding roll
1
Fuse
4
2A/7A
Video
1
Application
Applying to indoor and outdoor car sticker,photo and video,rimless no painting mounting and so on.
SHIPPING
1.We will ship your item by FedEx, DHL, UPS, EMS, e-Package etc with the tracking number showed on ebay.
2.Your item will be shipped within 1-3 working days after clear payment .
3.The shipping time varies. If by FedEX, DHL,or UPS, 3-4 business days to USA,5-7 business days to other most countries.
If by e-packet,7-15 days to USA,and 2-4 weeks to other most countries.
4.Due to the local dispatch or other reasons, sometimes the shipping time will be delay. Please kindly understand Uncertainties by the delivery company. We will track the item all the time until it is reached to you.
PAYMENTS
1. we accept: Paypal and some other payment method.
2. We will very appreciate if you can pay for the order after your ordering within 1-3 working days so that we can provide you the best services.
3. Please list your special requests in Note after payment. (color, packages, etc.)
Feedback
1.If you have any problems or concerns to your order or products, please message us and give us a chance to assist before you leave negative feedback.
2.We believe that we can produce a positive outcome to any situation to earn your like
s.
3.Your satisfaction is guaranteed.